How to clean puch moped body
- HOW TO CLEAN PUCH MOPED BODY HOW TO
- HOW TO CLEAN PUCH MOPED BODY INSTALL
- HOW TO CLEAN PUCH MOPED BODY MANUAL
- HOW TO CLEAN PUCH MOPED BODY FREE
This video shows you how to make a small modification to the hub to make the A3 shoes fit on your A35.
HOW TO CLEAN PUCH MOPED BODY INSTALL
Install A3 clutch shoes on an A35 clutch hubĪ3 clutch shoes are better than A35 clutch shoes, but you can't directly swap A3 shoes onto an A35 hub.How to change the transmission fluid on a Tomos A35 and/or A55. Tomos A35/A55 Transmission Fluid Change.This blog has embedded videos of the disassembly of a ZA50 engine.Ī video about the operation of the Puch ZA50 starter clutch cable operation.Īn overview of the flywheel, points, transmission, and how to replace the transmission fluid on a Tomos A3 motor.Ī look at the gears and internal spring mechanism on a Tomos A3 engine. Puch ZA50 disassembly NOT using factory Puch tools.Ī quick tear down of the second speed drive gear and some talk about the shift dampeners (pucks) on the Puch ZA50. Puch ZA50 engine disassembly using factory Puch tools. How to set the timing on a Puch E50 engine.Ī demonstration of how to clean the ignition points on a moped.Ī repair video for Tomos ignition - direct wiring and spark test. Need to get under your flywheel but don't have a puller? Watch this! How to check and adjust moped spark plugs. How to locate and remove a moped spark plug. Spark plug, points, flywheel, magneto, lighting, wiring, etc.Ī video on how to change a spark plug. Here is a short video for cleaning a Dellorto SHA 12:10, 12:12 or 13:13 Vespa moped Electrical System How to re-jet the carburetor on a Tomos A55. How to remove, clean, and reattach a Dellorto.
How to adjust the choke release on a Dellorto carb.Īdjusting the idle screw and throttle cable on a Dellorto carb.
How a Dellorto choke functions and how to take one apart/put it back together. How to install the throttle cable on a Bing carburetor. How to reattach a Bing carburetor to a Puch Maxi (can also apply to other mopeds).Īdjusting the idle speed and air intake speed screws on a Bing carburetor. Instructions for reassembling a Bing carburetor. Instructions for cleaning a Bing carburetor (can also be applied to other carburetor brands). How to remove the top half of a Bing carburetor. How to remove a Bing carburetor from a Puch Maxi (can also be applied to other mopeds). Information about the functions of the pieces of a Bing carburetor (can also apply to other carburetor brands).
HOW TO CLEAN PUCH MOPED BODY MANUAL
See also: Repair manual links Fuel System If you haven't made any, get to work already! A picture says a thousand words, but a video says a million.
HOW TO CLEAN PUCH MOPED BODY FREE
Please feel free to link to any repair videos you have made. Refer to this instructable if you don't know how.This article is a collection of links to moped-related repair videos. Don't forget to fill up on motor on motor oil. Once all screws are going in smoothly, turn them all in the rest of the way, then tighten them down good. turn the first screw in 2 turns, then the opposite screw 2 times. It sux! I ALWAYS start the screws 1 at a time. You'll have to mave the arm back while installing the clutch cover onto the motor.
It's a real pain in thee arse to do this after everything is back together. Be sure to put the clutch cable back in the arm. I find that putting the (4) screws in first, then the gasket onto the screws, helps keep everything together when fitting things back up. "Yamabond" is good stuff, but there's other types that are also good. I like to put some liquid gasket onto both surfaces before I put everything back together. Replace your clutch gasket if the old one is trashed. If you have old gasket crud on there, carefully scrape it off. wipe down both contact surfaces where the gasket goes. Take a small flat screwdriver and scrape out the crap from the grove where the circle spring sits. Determine if you need to replace your clutch.